Linux Hardware Compatibility: W311MI

This is just to let others know what piece of hardware worked during my linux experiments:

 

 

dmesg output

<5>[    0.000000] Linux version 2.6.31.6_SMP_820 (bdietrich@brad-ux) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #96 SMP Tue                Feb 8 12:08:54 PST 2011
<4>[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
<4>[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
<4>[    0.000000] Machine: Oxsemi NAS
<5>[    0.000000] 1 memory region
<4>[    0.000000] Ignoring unrecognised tag 0x00000000
<4>[    0.000000] Memory policy: ECC disabled, Data cache writealloc
<7>[    0.000000] On node 0 totalpages: 32768
<7>[    0.000000] free_area_init_node: node 0, pgdat c0401080, node_mem_map c0424000
<7>[    0.000000]   Normal zone: 256 pages used for memmap
<7>[    0.000000]   Normal zone: 0 pages reserved
<7>[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
<4>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
<5>[    0.000000] Kernel command line: root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x0               0,0×30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
<4>[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
<6>[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<6>[    0.000000] Memory: 128MB = 128MB total
<5>[    0.000000] Memory: 125496KB available (3712K code, 275K data, 120K init, 0K highmem)
<6>[    0.000000] Hierarchical RCU implementation.
<6>[    0.000000] NR_IRQS:96
<4>[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
<4>[    0.010000] Console: colour dummy device 80×30
<6>[    0.010000] console [ttyS0] enabled
<6>[    0.020000] Calibrating delay loop… 279.34 BogoMIPS (lpj=1396736)
<6>[    0.260000] Security Framework initialized
<4>[    0.260000] Mount-cache hash table entries: 512
<6>[    0.270000] CPU: Testing write buffer coherency: ok
<6>[    0.270000] Calibrating local timer… 350.00MHz.
<4>[    0.340000] CPU1: Booted secondary processor
<6>[    0.440000] Calibrating delay loop… 279.34 BogoMIPS (lpj=1396736)
<6>[    0.670000] Brought up 2 CPUs
<6>[    0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
<6>[    0.690000] NET: Registered protocol family 16
<6>[    0.690000] Number of DMA channels = 4, version = 4
<6>[    0.700000] Reserving a DMA channel for DirectRAID
<6>[    0.700000] Allocating 389 SRAM generic DMA descriptors
<4>[    0.720000] bio: create slab <bio-0> at 0
<5>[    0.730000] SCSI subsystem initialized
<7>[    0.730000] libata version 3.00 loaded.
<6>[    0.750000] NET: Registered protocol family 2
<6>[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[    0.760000] Switched to NOHz mode on CPU #0
<6>[    0.760000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>[    0.760000] Switched to NOHz mode on CPU #1
<6>[    0.770000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
<6>[    0.780000] TCP: Hash tables configured (established 4096 bind 4096)
<6>[    0.780000] TCP reno registered
<6>[    0.790000] NET: Registered protocol family 1
<4>[    0.790000] Create fragment cache
<6>[    0.800000] fuse init (API version 7.12)
<6>[    0.800000] msgmni has been set to 245
<6>[    0.810000] alg: No test for stdrng (krng)
<6>[    0.810000] io scheduler noop registered
<6>[    0.820000] io scheduler anticipatory registered
<6>[    0.820000] io scheduler deadline registered
<6>[    0.830000] io scheduler cfq registered (default)
<6>[    0.850000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
<6>[    0.860000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
<6>[    0.880000] brd: module loaded
<6>[    0.890000] loop: module loaded
<6>[    0.890000] ox820sata: OX820 sata core.
<6>[    0.890000] scsi0 : oxnassata
<6>[    0.900000] scsi1 : oxnassata
<6>[    0.900000] ata1: SATA max UDMA/133 irq 50
<6>[    0.910000] ata2: SATA max UDMA/133 irq 50
<3>[    0.910000] ox820sata: reseting SATA core
<6>[    1.270000] ata1: SATA link down (SStatus 0 SControl 300)
<3>[    1.270000] ox820sata: reseting SATA core
<6>[    1.630000] ata2: SATA link down (SStatus 0 SControl 300)
<6>[    1.630000] tun: Universal TUN/TAP device driver, 1.6
<6>[    1.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<4>[    1.640000] NAND: Page read time 40ms
<6>[    1.650000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
<6>[    1.660000] Scanning device for bad blocks
<4>[    1.670000] Bad eraseblock 225 at 0x000001c20000
<4>[    1.680000] Bad eraseblock 273 at 0x000002220000
<5>[    1.740000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
<5>[    1.750000] 0x000000000000-0x000000e00000 : "boot"
<5>[    1.750000] 0x000000e00000-0x000008000000 : "rootfs"
<5>[    1.760000] UBI: attaching mtd2 to ubi0
<5>[    1.760000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
<5>[    1.770000] UBI: logical eraseblock size:    129024 bytes
<5>[    1.770000] UBI: smallest flash I/O unit:    2048
<5>[    1.780000] UBI: sub-page size:              512
<5>[    1.780000] UBI: VID header offset:          512 (aligned 512)
<5>[    1.790000] UBI: data offset:                2048
<5>[    2.200000] UBI: attached mtd2 to ubi0
<5>[    2.200000] UBI: MTD device name:            "rootfs"
<5>[    2.210000] UBI: MTD device size:            114 MiB
<5>[    2.210000] UBI: number of good PEBs:        910
<5>[    2.220000] UBI: number of bad PEBs:         2
<5>[    2.220000] UBI: max. allowed volumes:       128
<5>[    2.220000] UBI: wear-leveling threshold:    4096
<5>[    2.230000] UBI: number of internal volumes: 1
<5>[    2.230000] UBI: number of user volumes:     1
<5>[    2.240000] UBI: available PEBs:             0
<5>[    2.240000] UBI: total number of reserved PEBs: 910
<5>[    2.250000] UBI: number of PEBs reserved for bad PEB handling: 9
<5>[    2.250000] UBI: max/mean erase counter: 2/0
<5>[    2.260000] UBI: image sequence number: 0
<5>[    2.260000] UBI: background thread "ubi_bgt0d" started, PID 275
<6>[    2.270000] mice: PS/2 mouse device common for all mice
<6>[    2.270000] TCP cubic registered
<6>[    2.280000] NET: Registered protocol family 10
<6>[    2.280000] NET: Registered protocol family 17
<6>[    2.290000] RPC: Registered udp transport module.
<6>[    2.290000] RPC: Registered tcp transport module.
<5>[    2.520000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
<5>[    2.530000] UBIFS: file system size:   114315264 bytes (111636 KiB, 109 MiB, 886 LEBs)
<5>[    2.540000] UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
<5>[    2.540000] UBIFS: media format:       w4/r0 (latest is w4/r0)
<5>[    2.550000] UBIFS: default compressor: zlib
<5>[    2.550000] UBIFS: reserved for root:  0 bytes (0 KiB)
<4>[    2.560000] VFS: Mounted root (ubifs filesystem) on device 0:10.
<6>[    2.570000] Freeing init memory: 120K
<5>[    3.440000] Probing for Synopsis GMAC, unit 0
<6>[    3.450000] eth0: Tuning GMAC 0 RGMII timings
<6>[    3.450000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
<5>[    3.460000] eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
<5>[    3.470000] eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
<5>[    3.480000] eth0: Ethernet addr: 00:30:e0:00:00:00
<6>[    3.500000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
<6>[    3.500000] Offload is not active on eth0
<6>[    3.510000] Alloc'ing ARM descs 10240 bytes
<6>[    3.510000] eth0: Resetting GMAC
<6>[    3.520000] eth0: GMAC reset complete
<6>[    3.520000] eth0: Setting Rx flow control thresholds for LAN port
<6>[    4.080000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
<6>[    4.580000] eth0: link down
<6>[    6.540000] ADDRCONF(NETDEV_UP): eth0: link is not ready
<6>[    8.080000] eth0: link up, 1000Mbps, full-duplex, using pause, lpa 0xCDE1
<6>[    8.080000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
<6>[   10.690000] usbcore: registered new interface driver usbfs
<6>[   10.700000] usbcore: registered new interface driver hub
<6>[   10.710000] usbcore: registered new device driver usb
<6>[   10.760000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[   10.770000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
<6>[   10.780000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
<6>[   10.810000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
<6>[   10.830000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
<6>[   10.840000] usb usb1: configuration #1 chosen from 1 choice
<6>[   10.840000] hub 1-0:1.0: USB hub found
<6>[   10.850000] hub 1-0:1.0: 2 ports detected
<6>[   10.940000] Initializing USB Mass Storage driver…
<6>[   10.940000] usbcore: registered new interface driver usb-storage
<6>[   10.950000] USB Mass Storage support registered.
<6>[   11.170000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
<4>[   11.330000] ufsd: module license 'Commercial product' taints kernel.
<4>[   11.340000] Disabling lock debugging due to kernel taint
<6>[   11.470000] usb 1-1: configuration #1 chosen from 1 choice
<6>[   11.560000] hub 1-1:1.0: USB hub found
<6>[   11.570000] hub 1-1:1.0: 4 ports detected
<5>[   11.610000] ufsd: driver 8.3 (008_A) with acl LBD=ON with ioctl loaded at bf078000
<5>[   11.610000] NTFS read/write support included
<5>[   11.610000] Hfs+/HfsX read/write support included
<6>[   11.870000] usb 1-1.2: new high speed USB device using oxnas-ehci and address 3
<4>[   11.960000] rtusb init rt2870 —>
<6>[   11.970000] usbcore: registered new interface driver rt2870
<4>[   12.000000] Cloud Engines XCE Init [Version: 2.5.9.1]
<6>[   12.010000] XCE: CPU MEMORY MAP:
<6>[   12.010000] XCE:   — 0x00001000 – 0xbeffffff (3055 MB)  User Space Mappings
<6>[   12.020000] XCE:   — 0xbf000000 – 0xbfffffff (  16 MB)  Kernel module space
<6>[   12.020000] XCE:   — 0xc0000000 – 0xc7ffffff ( 128 MB)  Kernel direct-mapped ram
<6>[   12.030000] XCE:   — 0xc8800000 – 0xecffffff ( 584 MB)  Kernel vmalloc space
<6>[   12.040000] XCE:   — 0xed000000 – 0xfeffffff ( 287 MB)  Kernel platform space
<6>[   12.040000] XCE: CPU FEATURES:
<6>[   12.050000] XCE:   — I Cache:         enabled
<6>[   12.050000] XCE:   — D Cache:         enabled
<6>[   12.060000] XCE:   — Branch Predict:  disabled
<6>[   12.060000] XCE:   — MMU:             enabled
<6>[   12.070000] XCE:   — Alignment Abort: disabled
<6>[   12.070000] XCE: BLPARAMS: Locating parameter block…
<6>[   12.080000] XCE: BLPARAMS: reading 2048 bytes @ a0000
<6>[   12.080000] XCE: Loaded Property Size: 2048
<6>[   12.090000] XCE:    – 'cesvcid' -> '7BR8RPYW6XVXK3F2PKS978HRTN'
<6>[   12.090000] XCE:    – 'ceboardver' -> 'PPV3'
<4>[   12.100000] XCE: No board spec found matching boardid 'PPV3' — Using 'PPRO1'
<6>[   12.100000] XCE: Current GPIO State:
<6>[   12.110000] XCE:  GPIO A input:        0xf679fff7
<6>[   12.110000] XCE:  GPIO A OE status:    0x00000000
<6>[   12.120000] XCE:  GPIO A IRQ enable:   0x00000000
<6>[   12.120000] XCE:  GPIO A IRQ event:    0x00000000
<6>[   12.130000] XCE:  GPIO A output state: 0x00000000
<6>[   12.130000] XCE:  GPIO B input:        0x0003ffff
<6>[   12.140000] XCE:  GPIO B OE status:    0x00030000
<6>[   12.140000] XCE:  GPIO B IRQ enable:   0x00000000
<6>[   12.150000] XCE:  GPIO B IRQ event:    0x00000000
<6>[   12.150000] XCE:  GPIO B output state: 0x00030000
<6>[   12.290000] XCE: BLPARAMS: Locating parameter block…
<6>[   12.290000] XCE: BLPARAMS: reading 2048 bytes @ a0000
<6>[   12.300000] XCE: BLPARAMS: reading 2048 bytes @ a0800
<6>[   12.310000] XCE: BLPARAMS: reading 2048 bytes @ a1000
<6>[   12.310000] XCE: BLPARAMS: reading 2048 bytes @ a1800
<6>[   13.990000] usb 1-1.2: configuration #1 chosen from 1 choice
<6>[   14.010000] scsi2 : SCSI emulation for USB Mass Storage devices
<7>[   14.020000] usb-storage: device found at 3
<7>[   14.020000] usb-storage: waiting for device to settle before scanning
<6>[   17.800000] XCE: XCE: LED -> CONNECTED
<7>[   18.200000] eth0: no IPv6 routers present
<5>[   19.020000] scsi 2:0:0:0: Direct-Access        Mass  Storage Device        PQ: 0 ANSI: 0
<5>[   19.050000] sd 2:0:0:0: [sda] 625142446 512-byte logical blocks: (320 GB/298 GiB)
<7>[   19.050000] usb-storage: device scan complete
<5>[   19.050000] sd 2:0:0:0: [sda] Write Protect is off
<7>[   19.060000] sd 2:0:0:0: [sda] Mode Sense: 03 00 00 00
<3>[   19.060000] sd 2:0:0:0: [sda] Assuming drive cache: write through
<3>[   19.070000] sd 2:0:0:0: [sda] Assuming drive cache: write through
<6>[   19.070000]  sda: sda1
<3>[   19.220000] sd 2:0:0:0: [sda] Assuming drive cache: write through
<5>[   19.220000] sd 2:0:0:0: [sda] Attached SCSI disk
<5>[   19.930000] ufsd: use builtin utf8 instead of kernel utf8
<5>[   20.130000] ufsd: sda1 without journal
<6>[  517.820000] XCE: BLPARAMS: Locating parameter block…
<6>[  517.830000] XCE: BLPARAMS: reading 2048 bytes @ a0000
<6>[  517.840000] XCE: BLPARAMS: reading 2048 bytes @ a0800
<6>[  517.840000] XCE: BLPARAMS: reading 2048 bytes @ a1000
<6>[  517.850000] XCE: BLPARAMS: reading 2048 bytes @ a1800
 

 

.

 

Tagged , , , , , . Bookmark the permalink.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

  • IGlr